Now, if you have different types of earbuds, that’s fine. Just make sure they are flexible and not flat-shaped. Beats by dre store can offer you more choices.
The way you best isolate sound is my twisting the earbuds into your canal. When you twist the earbuds into your canal, it creates somewhat of a suction, and they adhere closely to your skin. This delivers great sound directly into your experience.
There seem to be two main camps when it comes to earbud fit: those who say they should fit snugly inside the ear canal to obtain optimum sound quality, and those who maintain that a looser fit better protects the delicate ear muscles and allows for more physical comfort. While each side has valid points, the ultimate decision of comfort is determined by the wearer.
Those who say earbuds should fit tightly attest that a slight bit of gentle pressure maximizes the absorption of sound, allowing for the best listening experience. However, some people find the sensation of hard plastic rubbing against their inner ear unnerving and sometimes even uncomfortable. On the other hand, looser earbuds, while undoubtedly more comfortable, allow less sound to penetrate the skin and therefore make for less of a “surround sound” experience. The best solution to each of the issues is to seek out earbuds that have flexible, gel-like tips rather than hard, round buds, as the softer headphones mold well to the shape of each wearer’s ear. Often, this typ e of headphone is available with rubber or silicone tips, both of which are far more comfortable and actually help block out much of the incoming sound that interferes with the music being played. Beats by dre store can offer you more choices
Another common problem in earbud fit is that these smaller headphones tend to fall out or slip out of place as the wearer moves about, as in cases of running or exercising. The easiest solution to this problem is to purchase a set of earbud clips that are shaped similarly to the human ear and curve along the outside of the ear itself. These clips help hold the earbuds in place while still allowing the user to comfortably move about and not interfering with one’s hairstyle or hat. Beats in ear do this better than other brand.
Recommend:http://tangenaieosr.weebly.com/1/post/2012/09/when-dr-dre-monster-broken.html

I think you'll agree, headphone cables break more often than we'd like. like dr dre monster. These tiny pieces of plastic, rubber and copper put up with a lot of stress, especially when used in conjunction with portable media players and during daily commutes.
You can use a pair of scissors or a knife to cut off the old jack plug. If it's a molded plug, throw it away—it's no use.
You will need to buy a new jack plug to replace it. Assuming you are replacing one of the smaller plugs on a standard pair of headphones or earbuds, the item you need is called a 3.5mm stereo jack plug and you can buy it easily online from an electronic parts shop or from an electronics store if you have one nearby.
Prepare your cable.
Now strike a match and briefly heat the ends of all three wires to burn off the insulating covering.
Now, before you solder the wires, you need to thread the cable through the top (plastic) part of the plug (in other words, the cover) so it's ready to screw back on to the metal base afterward. It's very easy to forget this step—and if you do forget, you'll have to take the wires off again and repeat the process, which (believe me) is very annoying. Buy beats by dre will be a better choice.
It can be quite tricky to support such a small jack plug while you're soldering it. But, whatever you do, DON'T under any circumstances hold or touch the bottom of the jack plug while you solder the top it: the heat will travel through the electrical pins in about a second and burn your fingers. I know—I've made this mistake more than once! If you get the red and green wires mixed up, your headphones will still work but the left and right channels will be switched over.
If you really want to be sure about your stereo, you can check your left and right channels with this little sound tester I've made (powered by the Audio Player Wordpress Plugin). You'll hear a short audio message at the start in both headphones. Then you should hear a plucked note only in the left headphone followed by a note only in the right headphone.
Before you do that, you can buy a cheap dre beats to have a try.
Recommend:http://tangenaieosr.weebly.com/1/post/2012/08/how-can-we-connect-monster-dre-headphone-to-laptop.html